• Home
  • Blog
  • Creating 3D Curves and Splitting Faces in Onshape

Creating 3D Curves and Splitting Faces in Onshape

Creating 3D Curves and Splitting Faces in Onshape

Complex geometry often begins with a simple design need: route a hose around an obstacle, define a flowing transition, add a groove that follows a curved housing, or divide a surface into regions for later features. A flat sketch may not be enough when the path needs to move through three dimensions.

That’s where 3D curves come in. In Onshape, a spatial curve can define a route or guide the creation of other geometry. Once the curve is in place, you can use suitable geometry derived from it to split a face and create a clear boundary for downstream modeling.

The key is to treat the curve and the split as connected steps in a modeling workflow. The curve describes the intended path; the split turns that path into useful model geometry.

Why create a curve in 3D?

A sketch is generally created on a plane. That’s ideal for profiles, layouts, and paths that remain flat. But many real design paths don’t stay on one plane.

For example, a cable route may need to travel forward, rise over a bracket, and then turn toward a connector. A trim line on a product housing might cross a surface that curves in more than one direction. Trying to approximate these paths with several separate planar sketches can create extra geometry and make the model harder to edit.

A 3D curve can help when you need to:

  • Define a route that passes through space
  • Guide a sweep or loft
  • Establish a boundary across a curved face
  • Plan the path of a hose, cable, or tube
  • Create reference geometry for a surface feature
  • Divide a face into regions for later detailing

Before building the curve, decide what it needs to accomplish. Is it primarily a visual boundary? Does it need to meet exact endpoints? Does it need a particular length or clearance? Those decisions influence how you create and constrain it.

Plan the route before modeling it

It’s tempting to start by moving points until the curve looks right. That can work for a quick concept, but it often creates a path that’s difficult to refine later.

Start by identifying:

  1. The start and end points. These may be connector locations, edges, vertices, or reference points.
  2. Important intermediate locations. Use only the points needed to control the route.
  3. Clearance requirements. Check the path against nearby parts and obstacles.
  4. The intended use. A curve used for a sweep may need different control from one used only as a visual guide.
  5. The required length or shape. If the route must fit a fixed length, account for that early.

This quick planning step helps keep the curve purposeful. It also gives you stable references to use if the surrounding design changes.

Creating a 3D curve with Routing Curve

Onshape’s Routing Curve feature is designed for defining paths in three dimensions. It can be useful for routing applications and other geometry that needs to follow a controlled spatial path.

A general workflow looks like this:

  1. Establish the route references

    Identify the locations the curve must pass through. Depending on your model, these may be existing vertices, points, edges, or other references. Stable references make it easier to update the curve if you later revise the part.

  2. Create the curve

    Start a Routing Curve feature and define the route using the appropriate points and references. Build the curve in the context of the surrounding geometry so you can see how it passes through the model.

  3. Refine the shape

    Adjust the control points to shape the curve. If the path has several bends, consider editing related control points together so the overall route remains smooth and intentional.

    Avoid adding points simply to force a curve into place. Too many control points can make the curve wavy and difficult to adjust. Begin with a simple route and add control only where the shape needs it.

  4. Set a target length if needed

    When the route must meet a defined length, use the target-length option and refine the curve around that requirement. A length target can help with cable and hose layouts, but it doesn’t guarantee that the path has adequate clearance or the desired bend shape. Check those conditions separately.

  5. Review the route data

    The routing curve table can help you inspect the curve’s locations and bends. Use it to review the route and make deliberate changes rather than relying only on the model’s current camera view.

  6. Inspect the curve from several directions

    Rotate the model and check the curve from the front, top, and side. A curve can appear clear from one angle while crossing a nearby face or part from another.

Turning a curve into a face split

A curve can define where you want a face boundary, but the selected splitting tool must intersect the target geometry in a way the Split feature can use. Depending on the shape and workflow, you may need to extend the curve or use a surface created from it as the splitting tool.

The general process is:

  1. Select the target face or body.
  2. Start the Split feature.
  3. Choose the split type that matches the geometry you want to divide.
  4. Select the curve, surface, or other suitable splitting tool.
  5. Review the preview and confirm where the new boundary will appear.
  6. Accept the feature and inspect the resulting edges and regions.

After the split, the divided face can support additional modeling steps. For example, you might use the new boundary to define a groove, create a panel seam, or separate an area for a surface detail.

Worked example: adding a curved channel to a housing

Imagine a curved electronics housing with a cable that exits near the rear and follows the outside of the enclosure toward a side connector. You want to add a shallow channel along that path.

Step 1: Define the cable route

Create a Routing Curve from the cable’s starting location to its endpoint. Add intermediate control points where the route must rise, turn, or pass around a mounting feature.

Keep the route simple. If the cable needs to curve around a boss, use enough control to define that bend without adding unnecessary points elsewhere.

Step 2: Check clearance

Rotate the housing and inspect the route from multiple angles. Confirm that it clears nearby bosses, ribs, and mounting features. If the curve passes too close to the housing or another part, adjust the relevant points before creating more geometry.

Step 3: Create geometry for the channel boundary

If the Routing Curve alone does not provide a suitable splitting tool, use it to guide or define a surface that intersects the housing. The surface should cross the face along the desired channel path and extend far enough to create a clean split.

Step 4: Split the face

Use the surface or other suitable geometry with the Split feature. Check the preview closely. The resulting boundary should follow the intended route and divide the housing face where the channel will be added.

Step 5: Build the channel

Use the split boundary as a reference for the next feature. Depending on the design, you might create a sketch from the new edge, offset a region, or use another feature to form the channel.

Step 6: Review the final shape

Inspect the channel and its transitions. Check that it follows the cable route, maintains the intended wall thickness, and doesn’t create awkward edges at the ends.

This approach separates the design into understandable stages: route, surface or tool geometry, split, and detail. If the cable path changes later, you can revise the route and update the dependent features.

Why might a split fail?

If the Split feature doesn’t produce the expected result, check the interaction between the splitting tool and the target geometry first.

The tool doesn’t intersect the face

A curve or surface that stops short of the face cannot divide it. Extend the tool or adjust its position so it crosses the target.

The tool only touches the face

A tangent contact may not create a clear division. Move or extend the tool so it passes through the face rather than merely touching it.

The curve lies on a different plane or surface

A 3D curve may be close to the target but not actually lie on or intersect it in the way the operation requires. Check its position in all three dimensions.

The target selection is too broad

If the model has several faces or bodies, confirm you selected the intended target. A preview can help reveal whether the tool is acting on the correct geometry.

The curve is too complex

An overly complicated curve can create awkward intersections or downstream features that are hard to maintain. Simplify the path and test the split again.

The splitting geometry ends at the boundary

A tool that terminates exactly at an edge can sometimes produce an unstable or incomplete result. Extending it past the target can make the intended intersection clearer.

Tips for an editable feature tree

A successful model isn’t only one that looks right. It should also be understandable when you return to it later.

  • Name important curves and surfaces by their purpose, such as “Cable Route” or “Channel Split Tool.”
  • Keep the route, splitting geometry, and final detail as separate features where practical.
  • Reference stable geometry, especially when the model is likely to change.
  • Avoid using temporary edges as critical references if they may disappear after a design edit.
  • Keep the curve simple, then add control only where the shape needs it.
  • Check downstream features after changing the curve, since edits may alter the split boundary.

Curve first, split second

3D curves give you a way to define paths that move through space. Splitting faces turns those paths—or geometry built from them—into boundaries that can drive additional features.

A reliable workflow begins with a clear route, uses stable references, and checks the curve from several viewpoints. Once the splitting tool intersects the target as intended, the new face boundary can support channels, seams, surface transitions, and other details.

For an intermediate or advanced Onshape project, try this workflow on a housing or panel with a curved feature. Build the route first, inspect it in 3D, then use suitable geometry to split the face. The result is easier to control when every step has a clear purpose.

Complete Onshape for Beginners: Project-Based Approach

Master Onshape from Scratch through Real-World Projects, Professional 3D Modeling, Assemblies, Technical Drawings, and Cloud-Based CAD Workflows.

Learn to create:

Precise 2D sketches
Professional 3D parts
Assemblies
Engineering drawings
Collaborative CAD projects
Explore the Course →